Moxa ioLogik E1260 Universal Controllers Ethernet Remote I/O
Introduction
Moxa ioLogik E1260 can handle a wide range of applications as it supports commonly used protocols for retrieving I/O data. SNMP and RESTful API protocols are frequently used by IT engineers, while OT engineers are more familiar with OT-based protocols like Modbus and EtherNet/IP. Moxa's Smart I/O enables both IT and OT engineers to conveniently retrieve data from the same I/O device. The Moxa ioLogik E1260 Series supports six different protocols, including Modbus TCP, EtherNet/IP, and Moxa AOPC for OT engineers, as well as SNMP, RESTful API, and Moxa MXIO library for IT engineers. It retrieves I/O data and converts it to any of these protocols simultaneously, making it easy to connect your applications.
Daisy-Chained Ethernet I/O Connection
This industrial Ethernet remote I/O comes with two switched Ethernet ports to allow for the free flow of information downstream to another local Ethernet device, or upstream to a control server via expandable daisy-chained Ethernet I/O arrays. Applications such as factory automation, security and surveillance systems, and tunneled connections can make use of daisy-chained Ethernet for building multidrop I/O networks over standard Ethernet cables. Many industrial automation users are familiar with multidrop as the configuration most typically used in fieldbus solutions. The daisy-chain capabilities supported by ioLogik Ethernet remote I/O units not only increase the expandability and installation possibilities for your remote I/O applications, but also lower overall costs by reducing the need for separate Ethernet switches. Daisy-chaining devices in this way will also reduce overall labor and cabling expenses.
Save Time and Wiring Costs with Peer-to-Peer Communications
In remote automation applications, the control room and sensors are often far removed, making wiring over long distances a constant challenge. With peer-to-peer networking, users may now map a pair of ioLogik Series modules so that input values will be directly transferred to output channels, greatly simplifying the wiring process and reducing wiring costs.
User-Definable Modbus TCP Addressing for Painless Upgrading of Existing Systems
For Modbus devices that are controlled and detected by fixed addresses, users need to spend a vast amount of time researching and verifying initial configurations. Users need to locate each device's networking details, such as I/O channels or vendor-defined addresses, to enable the initial or start address of a SCADA system or PLC. Devices that support user-definable Modbus TCP addressing offer greater flexibility and easier setup. Instead of worrying about individual devices, users simply configure the function and address map to fit their needs.
Push Technology for Events
When used with MX-AOPC UA Server, devices can use active push communications when communicating changes in state and/or events to a SCADA system. Unlike a polling system, when using a push architecture for communications with a SCADA system, messages will only be delivered when changes in state or configured events occur, resulting in higher accuracy and lower amounts of data that need to be transferred.
Features and Benefits
- User-definable Modbus TCP Slave addressing
- Supports RESTful API for IIoT applications
- Supports EtherNet/IP Adapter
- 2-port Ethernet switch for daisy-chain topologies
- Saves time and wiring costs with peer-to-peer communications
- Active communication with MX-AOPC UA Server
- Supports SNMP v1/v2c
- The ioSearch utility enables easy mass deployment
- and configuration, while configuration via web browser is user-friendly.
- I/O management is simplified with the MXIO library for Windows or Linux.
- Additionally, this product has Class I Division 2 and ATEX Zone 2 certifications.
- Models with wide operating temperature range are available for environments ranging from -40 to 75°C (-40 to 167°F).
Specifications
Input/Output Interface
|
Digital Input Channels |
ioLogik E1210 Series: 16 |
|
Digital Output Channels |
ioLogik E1211 Series: 16 |
|
Configurable DIO Channels (by jumper) |
ioLogik E1212 Series: 8 |
|
Relay Channels |
ioLogik E1214 Series: 6 |
|
Analog Input Channels |
ioLogik E1240 Series: 8 |
|
Analog Output Channels |
ioLogik E1241 Series: 4 |
|
RTD Channels |
ioLogik E1260 Series: 6 |
|
Thermocouple Channels |
ioLogik E1262 Series: 8 |
|
Isolation |
3k VDC or 2k Vrms |
|
Buttons |
Reset button |
Digital Inputs
|
Connector |
Screw-fastened Euroblock terminal |
|
Sensor Type |
Dry contact Wet contact (NPN or PNP) |
|
I/O Mode |
DI or event counter |
|
Dry Contact |
On: short to GND Off: open |
|
Wet Contact (DI to COM) |
On: 10 to 30 VDC Off: 0 to 3 VDC |
|
Counter Frequency |
250 Hz |
|
Digital Filtering Time Interval |
Software configurable |
|
Points per COM |
ioLogik E1210/E1212 Series: 8 channels ioLogik E1213 Series: 12 channels ioLogik E1214 Series: 6 channels ioLogik E1242 Series: 4 channels |
Digital Outputs
|
Connector |
Screw-fastened Euroblock terminal |
|
I/O Type |
ioLogik E1211/E1212/E1242 Series: Sink ioLogik E1213 Series: Source |
|
I/O Mode |
DO or pulse output |
|
Current Rating |
ioLogik E1211/E1212/E1242 Series: 200 mA per channel ioLogik E1213 Series: 500 mA per channel |
|
Pulse Output Frequency |
500 Hz (max.) |
|
Over-Current Protection |
ioLogik E1211/E1212/E1242 Series: 2.6 A per channel @ 25°C ioLogik E1213 Series: 1.5A per channel @ 25°C |
|
Over-Temperature Shutdown |
175°C (typical), 150°C (min.) |
|
Over-Voltage Protection |
35 VDC |
Relays
|
Connector |
Screw-fastened Euroblock terminal |
|
Type |
Form A (N.O.) power relay |
|
I/O Mode |
Relay or pulse output |
|
Pulse Output Frequency |
0.3 Hz at rated load (max.) |
|
Contact Current Rating |
Resistive load: 5A @ 30 VDC, 250 VAC, 110 VAC |
|
Contact Resistance |
100 milli-ohms (max.) |
|
Mechanical Endurance |
5,000,000 operations |
|
Electrical Endurance |
100,000 operations @ 5A resistive load |
|
Breakdown Voltage |
500 VAC |
|
Initial Insulation Resistance |
1,000 mega-ohms (min.) @ 500 VDC |
|
Note |
Ambient humidity must be non-condensing and remain between 5 and 95%. The relays may malfunction when operating in high condensation environments below 0°C. |
Physical Characteristics
|
Housing |
Plastic |
|
Dimensions |
27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in) |
|
Weight |
200 g (0.44 lb) |
|
Installation |
DIN-rail mounting, Wall mounting |
|
Wiring |
I/O cable, 16 to 26 AWG Power cable, 12 to 24 AWG |
Environmental Limits
|
Operating Temperature |
Standard Models: -10 to 60°C (14 to 140°F) Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
|
Storage Temperature (package included) |
-40 to 85°C (-40 to 185°F) |
|
Ambient Relative Humidity |
5 to 95% (non-condensing) |
|
Altitude |
4000 m |
Moxa ioLogik E1200 Series Available Models
|
Model Name |
Input/Output Interface |
Digital Output Type |
Operating Temp. |
|
ioLogik E1210 |
16 x DI |
- |
-10 to 60°C |
|
ioLogik E1210-T |
16 x DI |
- |
-40 to 75°C |
|
ioLogik E1211 |
16 x DO |
Sink |
-10 to 60°C |
|
ioLogik E1211-T |
16 x DO |
Sink |
-40 to 75°C |
|
ioLogik E1212 |
8 x DI, 8 x DIO |
Sink |
-10 to 60°C |
|
ioLogik E1212-T |
8 x DI, 8 x DIO |
Sink |
-40 to 75°C |
|
ioLogik E1213 |
8 x DI, 4 x DO, 4 x DIO |
Source |
-10 to 60°C |
|
ioLogik E1213-T |
8 x DI, 4 x DO, 4 x DIO |
Source |
-40 to 75°C |
|
ioLogik E1214 |
6 x DI, 6 x Relay |
- |
-10 to 60°C |
|
ioLogik E1214-T |
6 x DI, 6 x Relay |
- |
-40 to 75°C |
|
ioLogik E1240 |
8 x AI |
- |
-10 to 60°C |
|
ioLogik E1240-T |
8 x AI |
- |
-40 to 75°C |
|
ioLogik E1241 |
4 x AO |
- |
-10 to 60°C |
|
ioLogik E1241-T |
4 x AO |
- |
-40 to 75°C |
|
ioLogik E1242 |
4 DI, 4 x DIO, 4 x AI |
Sink |
-10 to 60°C |
|
ioLogik E1242-T |
4 DI, 4 x DIO, 4 x AI |
Sink |
-40 to 75°C |
|
ioLogik E1260 |
6 x RTD |
- |
-10 to 60°C |
|
ioLogik E1260-T |
6 x RTD |
- |
-40 to 75°C |
|
ioLogik E1262 |
8 x TC |
- |
-10 to 60°C |
|
ioLogik E1262-T |
8 x TC |
- |
-40 to 75°C |
Hot Tags: moxa iologik e1260, China, wholesale, online, order, Weidmuller ACT20P CI 2CO S 7760054115, weidmuller 1020200000, grs1042 hirschmann, spider 8tx rail switch, Moxa EDS 305 S SC, Hirschmann SSL20 8TX


