Weidmuller ACT20P-PRO DCDC II-S 1481970000
Weidmuller ACT20P-PRO DCDC II-S 1481970000

Weidmuller ACT20P-PRO DCDC II-S 1481970000

Weidmuller ACT20P-PRO DCDC II-S Analogue isolating amplifier, 24…230 V AC/DC power supply, Input : I/U universal, Output : I/U universal
Send Inquiry

Weidmuller ACT20P-PRO DCDC II-S 1481970000

 

Weidmuller ACT20P-PRO DCDC II-S Analogue isolating amplifier, 24…230 V AC/DC power supply, Input : I/U universal, Output : I/U universal

 

General ordering data

Version

Analogue isolating amplifier, 24…230 V AC/DC power supply, Input : I/U universal, Output : I/U universal

Order No.

1481970000

Type

ACT20P-PRO DCDC II-S

GTIN (EAN)

4050118291032

Qty.

1 items

 

Dimensions and weights

Depth

113.7 mm

Depth (inches)

4.476 inch

Height

119.2 mm

Height (inches)

4.693 inch

Width

12.5 mm

Width (inches)

0.492 inch

Net weight

130 g

 

Temperatures

Storage temperature

-40 °C...85 °C

Operating temperature

-20 °C...60 °C

Humidity at operating temperature

0...95 % (no condensation)

Humidity

5...95 %, no condensation

 

Probability of failure

SIL in compliance with IEC 61508

None

MTBF

76 a

 

Environmental Product Compliance

RoHS Compliance Status

Compliant with exemption

RoHS Exemption (if applicable/known)

7a, 7cI

REACH SVHC

Lead 7439-92-1

SCIP

2f6dd957-421a-46db-a0c2-cf1609156924

 

Input

Input current

configurable
± 0.1mA...± 100 mA

Input resistance, current

<5 mA: approx. 100 Ω; >5 mA: approx. 5 Ω

Input resistance, voltage

≥ 1 MΩ

Input signal

Voltage source
Current source

Input voltage

configurable
±40 mV…±300 V
Measuring range. min 40 mV

Number of inputs

1

Sensor

4- wire sensor (with own power supply)

 

Output

Cut-off frequency (-3 dB)

> 10 kHz/ <10 Hz

Load impedance current

≤ 600 Ω

load impedance voltage

≥ 1 kΩ

Offset current

20 µA

Offset voltage

<10 mV

Output current

configurable
0...±20 mA

Output voltage, note

Adjustable
0...±10 V

Type

active (as current source) or passive (as current sink)
connected control can be active / passive

 

Display

Display value

current measured value
Configuration data

Type

Dot-matrix display with ticker text, green

 

General data

Accuracy

<0.05 % of measuring range

Configuration

DIP switch
or via display and push-buttons

Galvanic isolation

3-way isolator
between input ⁄ output ⁄ supply

Nominal power consumption

2 VA

Operating altitude

≤ 2000 m

Power consumption

≤2.3 W

Protection degree

IP20

Rail

TS 35

Step response time

≤50 µs

Temperature coefficient

≤0,01% des Messbereichs⁄°C

Voltage supply

24…230 V DC ±20 %
24…230 V AC ±10 % @ 48…62 Hz

 

Insulation coordination

EMC standards

EN 61326-1

Galvanic isolation

3-way isolator
between input ⁄ output ⁄ supply

Impulse withstand voltage

5 kV (1.2/50 µs)

Insulation voltage

4 kVeff
input / output / power supply

Pollution severity

2

Rated voltage

600 V

Surge voltage category

II

 

Data for Ex applications (ATEX)

Marking

II 3 G Ex nA IIC T4 Gc

 

Connection data

Type of connection

Screw connection

Tightening torque, min.

0.4 Nm

Tightening torque, max.

0.6 Nm

Clamping range, rated connection

2.5 mm²

Clamping range, min.

0.5 mm²

Clamping range, max.

2.5 mm²

Wire connection cross section AWG, min.

AWG 26

Wire connection cross section AWG, max.

AWG 12

 

Important note

Product information

The universally configurable DC isolating amplifier ACT20P-PRO DCDC II isolates and converts analogue signals. An analogue input signal (current or voltage) is linearly converted into an analogue output signal (current or voltage) and galvanically isolated. The power supply is galvanically isolated from the input and output (3-way isolation).

Properties

  • universal wide-range voltage supply
  • universally configurable via DIP switch or via the LED display using control buttons
  • Active or passive signal output
  • Operating status display on a front panel LED
  • Galvanic 3-way isolation between input, output and supply.