Moxa AWK-4131A-EU-T
Moxa AWK-4131A-EU-T

Moxa AWK-4131A-EU-T

Moxa AWK-4131A-EU-T IP68 outdoor industrial AP/bridge/client meets the growing need for faster data transmission speeds by supporting 802.11n technology and allowing 2X2 MIMO communication with a net data rate of up to 300 Mbps. Moxa AWK-4131A-EU-T is compliant with industrial standards and approvals covering operating temperature, power input voltage, surge, ESD, and vibration. The two redundant DC power inputs increase the reliability of the power supply, and the AWK-4131A can be powered via PoE to make deployment easier. Moxa AWK-4131A-EU-T can operate on either the 2.4 GHz or 5 GHz bands and is backwards-compatible with existing 802.11a/b/g deployments to future-proof your wireless investments. The Wireless add-on for the MXview network management utility visualizes the AWK's invisible wireless connections to ensure wall-to-wall Wi-Fi connectivity.
Send Inquiry

Moxa AWK-4131A-EU-T Outdoor industrial IEEE 802.11a/b/g/n wireless AP/bridge/client

 

Features and Benefits

  • 2x2 MIMO 802.11a/b/g/n AP/bridge/client
  • Millisecond-level Client-based Turbo Roaming1
  • Easy setup and deployment with AeroMag
  • Wireless redundancy with AeroLink Protection
  • Easy network setup with Network Address Translation (NAT)
  • Rugged industrial design with integrated antenna and power isolation
  • IP68-rated weatherproof housing designed for outdoor applications and -40 to 75°C wide operating temperature range
  • Avoid wireless congestion with 5 GHz DFS channel support

 

Introduction

 

Moxa AWK-4131A-EU-T IP68 outdoor industrial AP/bridge/client meets the growing need for faster data transmission speeds by supporting 802.11n technology and allowing 2X2 MIMO communication with a net data rate of up to 300 Mbps. Moxa AWK-4131A-EU-T is compliant with industrial standards and approvals covering operating temperature, power input voltage, surge, ESD, and vibration. The two redundant DC power inputs increase the reliability of the power supply, and the AWK-4131A can be powered via PoE to make deployment easier. Moxa AWK-4131A-EU-T can operate on either the 2.4 GHz or 5 GHz bands and is backwards-compatible with existing 802.11a/b/g deployments to future-proof your wireless investments. The Wireless add-on for the MXview network management utility visualizes the AWK's invisible wireless connections to ensure wall-to-wall Wi-Fi connectivity.

 

Advanced 802.11n Industrial Wireless Solution

802.11a/b/g/n compliant AP/bridge/client for flexible deployment

Software-optimized for long-distance wireless communication with up to 1 km line of sight and external high-gain antenna (available only on 5 GHz)

Supports 60 clients connected concurrently

DFS channel support allows a wider range of 5 GHz channel selection to avoid interference from existing wireless infrastructure

 

Advanced Wireless Technology for Mission-critical Applications

Seamless roaming with client-based Turbo Roaming1 for < 150 ms roaming recovery time between APs (Client mode)

AeroMag support for error-free setup of your industrial applications' basic WLAN settings

Supports AeroLink Protection for creating a redundant wireless link (< 300 ms recovery time) between APs and their clients

1. The Turbo Roaming recovery time indicated herein is an average of test results documented, in optimized conditions, across APs configured with interference-free 20-MHz RF channels, WPA2-PSK security, and default Turbo Roaming parameters. The clients are configured with 3-channel roaming at 100 Kbps traffic load. Other conditions may also impact roaming performance. For more information about Turbo Roaming parameter settings, refer to the product manual.

 

Industrial Ruggedness

Integrated antenna and power isolation designed to provide 500 V insulation protection against external electrical interference

IP68-rated metal casing for complete ingress protection for any outdoor weather

-40 to 75°C wide operating temperature models available for smooth wireless communication in harsh environments

 

Wireless Network Management With MXview Wireless

Dynamic topology view shows the status of wireless links and connection changes at a glance

Visual, interactive roaming playback function to review the roaming history of clients

Detailed device information and performance indicator charts for individual AP and client devices

 

Specifications

 

WLAN Interface

WLAN Standards

802.11a/b/g/n

802.11i Wireless Security

Modulation Type

DSSS OFDM

MIMO-OFDM

Frequency Band for US (20 MHz operating channels)

2.412 to 2.462 GHz (11 channels)

5.180 to 5.240 GHz (4 channels)

5.260 to 5.320 GHz (4 channels)2

5.500 to 5.700 GHz (11 channels)2

5.745 to 5.825 GHz (5 channels)

Frequency Band for EU (20 MHz operating channels)

2.412 to 2.472 GHz (13 channels)

5.180 to 5.240 GHz (4 channels)

5.260 to 5.320 GHz (4 channels)2

5.500 to 5.700 GHz (11 channels)2

Frequency Band for JP (20 MHz operating channels)

2.412 to 2.484 GHz (14 channels)

5.180 to 5.240 GHz (4 channels)

5.260 to 5.240 GHz (4 channels)2

5.500 to 5.700 GHz (11 channels)2

Wireless Security

WEP encryption (64-bit and 128-bit)

WPA/WPA2-Enterprise (IEEE 802.1X/RADIUS, TKIP, AES)

WPA/WPA2-Personal

Transmission Rate

802.11b: 1 to 11 Mbps

802.11a/g: 6 to 54 Mbps

802.11n: 6.5 to 300 Mbps

Transmitter Power for 802.11a

23±1.5 dBm @ 6 to 24 Mbps

21±1.5 dBm @ 36 Mbps

20±1.5 dBm @ 48 Mbps

18±1.5 dBm @ 54 Mbps

Transmitter Power for 802.11n (5 GHz)

23±1.5 dBm @ MCS0/8 20 MHz

18±1.5 dBm @ MCS7/15 20 MHz

23±1.5 dBm @ MCS0/8 40 MHz

17±1.5 dBm @ MCS7/15 40 MHz

Transmitter Power for 802.11b

26±1.5 dBm @ 1 Mbps

26±1.5 dBm @ 2 Mbps

26±1.5 dBm @ 5.5 Mbps

25±1.5 dBm @ 11 Mbps

Transmitter Power for 802.11g

23±1.5 dBm @ 6 to 24 Mbps

21±1.5 dBm @ 36 Mbps

19±1.5 dBm @ 48 Mbps

18±1.5 dBm @ 54 Mbps

Transmitter Power for 802.11n (2.4 GHz)

23±1.5 dBm @ MCS0/8 20 MHz

18±1.5 dBm @ MCS7/15 20 MHz

23±1.5 dBm @ MCS0/8 40 MHz

17±1.5 dBm @ MCS7/15 40 MHz

Transmitter Power

 

US

EU

JP

5 GHz (UNII-3)

23 dBm

–

–

Note: Based on regional regulations, the maximum transmission power allowed on the UNII bands is restricted in the firmware, as indicated above.

Receiver Sensitivity for 802.11a (measured at 5.680 GHz)

Typ. -90 @ 6 Mbps

Typ. -88 @ 9 Mbps

Typ. -88 @ 12 Mbps

Typ. -85 @ 18 Mbps

Typ. -81 @ 24 Mbps

Typ. -78 @ 36 Mbps

Typ. -74 @ 48 Mbps

Typ. -72 @ 54 Mbps

Note: Due to a limitation in the receiver sensitivity performance for channels 153 and 161, it is recommended to avoid using these channels in your critical applications.

Receiver Sensitivity for 802.11n (5 GHz; measured at 5.680 GHz)

Typ. -69 dBm @ MCS7 20 MHz Typ. -71 dBm @ MCS15 20 MHz Typ. -63 dBm @ MCS7 40 MHz Typ. -68 dBm @ MCS15 40 MHz

Note: Due to a limitation in the receiver sensitivity performance for channels 153 and 161, it is recommended to avoid using these channels in your critical applications.

Receiver Sensitivity for 802.11b (measured at 2.437 GHz)

Typ. -93 dBm @ 1 Mbps

Typ. -93 dBm @ 2 Mbps

Typ. -93 dBm @ 5.5 Mbps

Typ. -88 dBm @ 11 Mbps

Receiver Sensitivity for 802.11g (measured at 2.437 GHz)

Typ. -88 dBm @ 6 Mbps

Typ. -86 dBm @ 9 Mbps

Typ. -85 dBm @ 12 Mbps

Typ. -85 dBm @ 18 Mbps

Typ. -85 dBm @ 24 Mbps

Typ. -82 dBm @ 36 Mbps

Typ. -78 dBm @ 48 Mbps

Typ. -74 dBm @ 54 Mbps

Receiver Sensitivity for 802.11n (2.4 GHz; measured at 2.437 GHz)

Typ. -70 dBm @ MCS7 20 MHz Typ. -69 dBm @ MCS15 20 MHz Typ. -67 dBm @ MCS7 40 MHz Typ. -67 dBm @ MCS15 40 MHz

WLAN Operation Mode

Access point, Client, Client-Router, Master, Slave, Sniffer

Antenna

External, 3/6 dBi, Omni-directional

WLAN Antenna Connector

2 N-type female

2. DFS (Dynamic Frequency Selection) channel support: In AP mode, when a radar signal is detected, the device will automatically switch to another channel. However, according to regulations, after switching channels, a 60-second availability check period is required before starting the service.

 

Ethernet Interface

Standards

IEEE 802.3 for 10BaseT

IEEE 802.3u for 100BaseT(X)

IEEE 802.3ab for 1000BaseT(X)

IEEE 802.3at for PoE

IEEE 802.1D-2004 for Spanning Tree Protocol

IEEE 802.1w for Rapid Spanning Tree Protocol

IEEE 802.1Q for VLAN Tagging

PoE Ports (10/100/1000BaseT(X), RJ45 connector)

1

 

Ethernet Software Features

Management

DHCP Server/Client, DNS, HTTP, IPv4, LLDP, Proxy ARP, SMTP, SNMPv1/v2c/v3, Syslog, TCP/IP, Telnet, UDP, VLAN, Wireless Search Utility, MXview, MXview Wireless, MXconfig

Routing

Static Route, NAT, Port forwarding

Redundancy Protocols

RSTP, STP

Security

HTTPS/SSL, RADIUS, SSH

Time Management

SNTP Client

 

Firewall

Filter

ICMP, MAC address, IP protocol, Port-based

 

Serial Interface

Console Port

RS-232, 8-pin RJ45

 

LED Interface

LED Indicators

PWR, FAULT, STATE, WLAN, LAN

 

Input/Output Interface

Alarm Contact Channels

Relay output with current carrying capacity of 1 A @ 24 VDC

Buttons

Reset button

Digital Inputs

+13 to +30 V for state 1

+3 to -30 V for state 0

Max. input current: 8 mA

 

Physical Characteristics

Housing

Metal

IP Rating

IP68

Dimensions

224 x 147.7 x 66.5 mm (8.82 x 5.82 x 2.62 in)

Weight

1,400 g (3.09 lb)

Installation

Wall mounting (standard), DIN-rail mounting (optional), Pole mounting (optional)

 

Power Parameters

Input Current

0.64 A @ 12 VDC, 0.16 A @ 48 VDC

Input Voltage

12 to 48 VDC, Redundant dual inputs, 48 VDC Power-over-Ethernet

Power Connector

M12 A-coded 5-pin male connector

Power Consumption

7.68 W (max.)

Reverse Polarity Protection

Supported

 

Environmental Limits

Operating Temperature

-40 to 75°C (-40 to 167°F)

Storage Temperature (package included)

-40 to 85°C (-40 to 185°F)

Ambient Relative Humidity

5 to 95% (non-condensing)

 

Standards and Certifications

EMC

EN 61000-6-2/-6-4

EMI

CISPR 32, FCC Part 15B Class A

EMS

IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV

IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m

IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV

IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV

IEC 61000-4-6 CS: 10 V

IEC 61000-4-8 PFMF

Radio

EN 300 328, EN 301 489-1/17, EN 301 893, FCC ID SLE-WAPN008, ANATEL, MIC, NCC, RCM, SRRC, WPC, KC

Safety

EN 60950-1, UL 60950-1

Vibration

IEC 60068-2-6

 

MTBF

Time

440,764 hrs

Standards

Telcordia SR332

 

Package Contents

Device

1 x AWK-4131A Series wireless AP/bridge/client

Installation Kit

1 x cap, female, metal, for M12 port

1 x cap, metal, for RJ45 port

1 x field-installable power plug

1 x field-installable RJ45 plug

1 x stick, transparent plastic, for field-installable plug

2 x wall-mounting kit

Antenna

2 x 2.4/5 GHz antenna

Documentation

1 x quick installation guide

1 x warranty card

 

Ordering Information

Model Name

Band

Standards

Operating Temp.

AWK-4131A-EU-T

EU

802.11a/b/g/n

-40 to 75°C

AWK-4131A-JP-T

JP

802.11a/b/g/n

-40 to 75°C

AWK-4131A-US-T

US

802.11a/b/g/n

-40 to 75°C

 

Accessories (sold separately)

 

Antennas

ANT-WDB-ONF-0709

7 dBi at 2.4 GHz or 9 dBi at 5 GHz, N-type (female), dual-band, omnidirectional antenna

ANT-WDB-ANM-0306

3 dBi at 2.4 GHz or 6 dBI at 5 GHz, N-type (male), omnidirectional antenna

ANT-WDB-ONM-0707

07 dBi at 2.4 GHz and 07 dBi at 5 GHz, N-type (male), dual-band omnidirectional antenna

ANT-WDB-ANM-0502

5 dBi at 2.4 GHz or 2 dBI at 5 GHz, N-type (male), omnidirectional antenna

ANT-WDB-ARM-02

2 dBi at 2.4 GHz or 2 dBi at 5 GHz, RP-SMA (male) omnidirectional rubber-duck antenna

ANT-WDB-ARM-0202

2 dBi at 2.4 GHz or 2 dBi at 5 GHz, RP-SMA (male), dual-band, omnidirectional antenna

ANT-WDB-PNF-1011

10 dBi at 2.4 GHz and 11 dBi at 5 GHz, N-type (female), dual-band directional antenna

MAT-WDB-CA-RM-2-0205

2.4/5 GHz, ceiling antenna, 2/5 dBi, MIMO 2x2, RP-SMA-type (male)

MAT-WDB-DA-RM-2-0203-1m

2.4/5 GHz, desktop antenna, 2/3 dBi, MIMO 2x2, RP-SMA-type (male), 1 m cable

MAT-WDB-PA-NF-2-0708

2.4/5 GHz, panel antenna, 7/8 dBi, MIMO 2x2, N-type (female)

ANT-WSB5-PNF-16

16 dBi at 5 GHz, N-type (female), single-band directional antenna

ANT-WSB-PNF-12-02

12 dBi at 2.4 GHz, N-type (female), single-band directional antenna

ANT-WSB-AHRM-05-1.5m

5 dBi at 2.4 GHz, RP-SMA (male), omnidirectional/dipole antenna, 1.5 m cable

 

Wireless Antenna Cables

A-CRF-NMNM-LL4-300

N-type (male) to N-type (male) LMR-400 Lite cable, 3 m

A-CRF-NMNM-LL4-600

N-type (male) to N-type (male) LMR-400 Lite cable, 6 m

A-CRF-NMNM-LL4-900

N-type (male) to N-type (male) LMR-400 Lite cable, 9 m

 

Wireless AP Connector Cables

M12A-8PFF-IP68

Field-installation A-coded M12 screw-in 8-pin connector, female connector female PIN

M12A-8PMM-IP68

Field-installation A-coded screw-in Gigabit Ethernet connector, 8-pin male M12 connector, IP68-rated

A-PLG-WPRJ

Field-installation RJ-type plug

 

Wireless Connector Caps

A-CAP-N-M

A-CAP-N-M

A-CAP-WPRJ45-MC

Metal cap with chain for RJ45 connector

 

Surge Arrestors

A-SA-NFNF-02

0 to 6 GHz, N-type (female) to N-type (female) surge arrester

A-SA-NMNF-02

0 to 6 GHz, N-type (male) to N-type (female) surge arrester

 

Wireless Adapters

A-ADP-RJ458P-DB9F-ABC01

DB9 female to RJ45 connector for the ABC-01 Series

 

Wireless Terminating Resistors

A-TRM-50-NM

50-ohm termination resistor with N-type male connector

 

Wall-Mounting Kits

WK-51-01

Wall mounting kit with 2 plates (51.6 x 67 x 2 mm) and 6 screws

 

Wireless AP Mounting Kits

WK-55

Wall mounting kit with 2 plates (55 x 34.5 x 2.5 mm) and 6 screws

 

Hot Tags: moxa awk-4131a-eu-t, China, wholesale, online, order, eds 208a mm sc, moxa eds 308 mm sc, moxa 5650 16, nport 5650, tcf142, moxa nport 5610 16